Series 7000 AC Vector Control

The Series 7000 AC Vector Control is designed for precision motor control in a wide variety of applications.

240 VAC Three Phase Input Units

Horsepower	1	2	3	5	7.5	10	15	20
Input Voltage	240	240	240	240	240	240	240	240
Input Current	4.1	7.7	12.7	19.5	27.3	35.0	51.6	68.2
Input KVA	1.7	3.20	5.28	8.11	11.35	14.55	21.45	28.35
Input Surge (Joules)	40	40	40	40	40	40	40	40
Output Voltage	240	240	240	240	240	240	240	240
Output Current	4.0	6.8	10.4	16.0	23.0	29.0	42.0	54.0
Output KVA	1.66	2.83	4.32	6.65	9.56	12.06	17.46	22.44
Efficiency (TYP)	94%	95%	95%	96%	96%	96%	96%	96%
Power Dissipation (W)	43	68	101	160	190	230	345	445
Basic Weight (lb.)	18	18	18	20	50	52	55	58
Shipping Weight (lb.)	22	22	22	24	55	57	60	63

480 VAC Three Phase Input Units

Horsepower
1 2 3 5 7.5 10 15 20

Input Voltage
480 480 480 480 480 480 480 480

Input Current
2.1 3.9 6.3 9.7 14.9 17.5 27.0 35.4

Input KVA
1.75 3.24 5.24 8.06 12.39 14.55 22.45 29.43

Input Surge (Joules)
80 80 80 80 80 80 80 80

Output Voltage
480 480 480 480 480 480 480 480

Output Current
2.0 3.4 5.2 8.0 12.0 14.5 22.0 28.0

Output KVA
1.66 2.83 4.32 6.65 9.98 12.06 18.29 23.29

Efficiency (TYP)
93% 94% 94% 96% 96% 96% 96% 96%

Power Dissipation (W)
51 82 125 160 190 230 345 445

Basic Weight (lb.)
19 19 19 19 49 50 55 56

Shipping Weight (lb.)
23 23 23 23 54 55 60 61

480 VAC Three Phase Input Units

Horsepower
25 30 40 50 60 75 100 125 150

Input Voltage
480 480 480 480 480 480 480 480 480

Input Current
45.4 53.4 69.1 88.7 102.4 123.7 172.6 221.6 246.5

Input KVA
35 45 58 74 86 103 144 185 205

Input Surge (Joules)
80 80 80 80 80 80 80 80 80

Output Voltage
480 480 480 480 480 480 480 480 480

Output Current
35.7 42 55 70 81 100 130 164 189

Output KVA
29.7 34.9 45.7 58.2 67.3 83.1 108.1 136.3 157.1

Efficiency (TYP)
97% 97% 97% 97% 97% 97% 97% 97% 97%

Power Dissipation (W)
440 510 664 955 1070 1270 1830 2170 2440

Basic Weight (lb.)
160 160 160 275 275 275 475 475 475

Shipping Weight (lb.)
184 184 184 316 316 316 546 546 546

Standard Features

Protection
- Instantaneous overcurrent trip 200%
- Ground fault trip
- Undervoltage trip (below 85% of rated)
- Overvoltage trip (above 110% of rated)
- Heatsink overtemperature
- Motor overtemperature
- Microprocessor watchdog timeout
- Internal and external memory check
- Excessive speed indication
- Loss of current feedback trip
- Loss of external dynamic breaking trip
- Excessive speed indication
Enclosures
- Chassis (1 - 5 HP)
- NEMA 1 (7.5 - 20 HP)
Encoder Input
- 700 ohms, 15 mA each
- 200 kHz Maximum Frequency - Standard
- 1mHz maximum frequency - Special Order
- Maximum recommended distance between encoder and control
  - Differential Input: 1000 ft
  - Single Ended Input: 30 ft
Encoder
- 1024 ppr with AB and complements
  (consult factory for other ppr)
- Z channel required for positioning
- Differential line driver or open collector with 470 ohm to 1.5K ohm pull-up resistor
Motor
- Standard NEMA B induction motor
  consult factory for other motor types
Keypad/Personality Module
- Local operators station
- Programmable display
- Programmer and personality module
Acceleration/Deceleration
- Linear acceleration and deceleration to base speed
  adjustable from 0.05 to 184.4 seconds (60 Hz) through software
Digital Inputs
- Customer 10-25 VAC/VDC source or dry contact
  each rated 20 mA maximum
Analog Inputs
- Bipolar
  - Three +/- 10 VDC differential inputs, independently configurable via software
  - 20 Kohms input impedance
- Unipolar
  - One 0 to +10 VDC max. differential input, independently configurable via software
  - 20 Kohms input impedance
  - Minimum burden resistance: 5 Kohms
Current loop Input
- One 4-20 mA differential input
- 200 ohms input impedance
Digital Outputs
- Eight open collector/relay drivers
  - 30 VDC maximum voltage
  - 100mA total maximum sink current per TB5 and TB6
- Each output is configurable within the limits of the drive software
Analog Outputs
- Two 0 to -5 VDC or 0 to +10 VDC, 10mA max.
- Jumper selectable output meter drivers
  - One proportional to % motor speed default setting
  - One proportional to % output current default setting
Power Supplies
- +10 and -10 VDC, 50mA max. total external load permitted
  Drift: 8.5 ppm/°C
- +15 VDC, 300 mA total external load permitted
- -15 VDC, 100 mA total external load permitted
- +5 VDC, 280 mA total external load permitted, connected to encoder terminal block P6
Communications
- RS-232/422 serial, jumper selectable
  8 bits, no parity, 1-stop bit
Baud Rates
- 1200, 2400, 4800, 9600 software selectable
- 1200 baud is default value
Maximum Cable Length
- 50 ft (15 meters) RS-232
- 3,300 ft (1000 meters) RS-422

Optional Features

Internal Dynamic Braking Module 1-20 HP
- 100% torque continuous
- 150% HP, 20 seconds max
- 20% duty cycle
Dynamic Braking Resistors 1-20 HP
- Supplied loose for panel mounting
- Provides up to 4 stops per minute with twice rated motor inertia
- For other application requirements, consult factory
Dynamic Braking Module 25-150 HP
- Supplied in 25 HP increments
- Up to 6 modules may be connected in parallel for 150 HP.
- Refer to Dynamic Braking Module technical Manual for details
Encoder Buffer/Loss of Feedback Board 1-150 HP
- Boosts encoder signals for particularly long encoder cable runs
- Consult factory for details
External Line Regeneration 1-150 HP
- 100% HP continuous
- 150% HP, 1 minute max
- Refer to Line Regeneration Technical Manual for details
External Power Supply
+15V, 1.5A
- Provides power for external relays and pushbuttons
- Allows for isolated power versus using control board power
External Power Supply
+5V, 3.0A
+15V, 800mA
- Same as above

Custom Power Technology, Inc.
N93 W14605 Whittaker Way
Menomonee Falls, WI 53051
Telephone: (262) 253-0880
Fax: (262) 253-0948
Email:Custom Power Technology